Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 | .. SPDX-License-Identifier: GPL-2.0+ U-Boot for BananaPi BPI-M2-PRO (S905X3) ======================================= BananaPi BPI-M2-PRO is a Single Board Computer manufactured by Sinovoip with the following specification: - Amlogic S905X3 Arm Cortex-A55 quad-core SoC - 2GB DDR4 SDRAM - 16GB eMMC - Gigabit Ethernet - RTL8821CU USB WiFi (a/b/g/n/ac) + BT 5.0 - HDMI 2.1 display - 40-pin GPIO header - 2x USB 3.0 Host - 1x DC Jack (power) - microSD - UART serial - Infrared receiver Schematics are available from the manufacturer: https://wiki.banana-pi.org/Banana_Pi_BPI-M2_Pro U-Boot Compilation ------------------ .. code-block:: bash $ export CROSS_COMPILE=aarch64-none-elf- $ make bananapi-m2pro_defconfig $ make U-Boot Signing with Pre-Built FIP repo -------------------------------------- .. code-block:: bash $ git clone https://github.com/LibreELEC/amlogic-boot-fip --depth=1 $ cd amlogic-boot-fip $ mkdir my-output-dir $ ./build-fip.sh bananapi-m2pro /path/to/u-boot/u-boot.bin my-output-dir U-Boot Manual Signing --------------------- Amlogic does not provide sources for the firmware and tools needed to create a bootloader image so it is necessary to obtain binaries from sources published by the board vendor: .. code-block:: bash $ wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz $ wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz $ tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz $ tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz $ export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH $ DIR=bananapi-m2pro $ git clone --depth 1 https://github.com/Dangku/amlogic-u-boot.git -b odroidg12-v2015.01-c4-m5 $DIR $ cd $DIR $ make bananapi_m2pro_defconfig $ make $ export UBOOTDIR=$PWD Go back to the mainline U-Boot source tree then: .. code-block:: bash $ mkdir fip $ wget https://github.com/BayLibre/u-boot/releases/download/v2017.11-libretech-cc/blx_fix_g12a.sh -O fip/blx_fix.sh $ cp $UBOOTDIR/build/scp_task/bl301.bin fip/ $ cp $UBOOTDIR/build/board/bananapi/bananpi_m5/firmware/acs.bin fip/ $ cp $UBOOTDIR/fip/g12a/bl2.bin fip/ $ cp $UBOOTDIR/fip/g12a/bl30.bin fip/ $ cp $UBOOTDIR/fip/g12a/bl31.img fip/ $ cp $UBOOTDIR/fip/g12a/ddr3_1d.fw fip/ $ cp $UBOOTDIR/fip/g12a/ddr4_1d.fw fip/ $ cp $UBOOTDIR/fip/g12a/ddr4_2d.fw fip/ $ cp $UBOOTDIR/fip/g12a/diag_lpddr4.fw fip/ $ cp $UBOOTDIR/fip/g12a/lpddr3_1d.fw fip/ $ cp $UBOOTDIR/fip/g12a/lpddr4_1d.fw fip/ $ cp $UBOOTDIR/fip/g12a/lpddr4_2d.fw fip/ $ cp $UBOOTDIR/fip/g12a/piei.fw fip/ $ cp $UBOOTDIR/fip/g12a/aml_ddr.fw fip/ $ cp u-boot.bin fip/bl33.bin $ sh fip/blx_fix.sh \ fip/bl30.bin \ fip/zero_tmp \ fip/bl30_zero.bin \ fip/bl301.bin \ fip/bl301_zero.bin \ fip/bl30_new.bin \ bl30 $ sh fip/blx_fix.sh \ fip/bl2.bin \ fip/zero_tmp \ fip/bl2_zero.bin \ fip/acs.bin \ fip/bl21_zero.bin \ fip/bl2_new.bin \ bl2 $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl30sig --input fip/bl30_new.bin \ --output fip/bl30_new.bin.g12a.enc \ --level v3 $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl3sig --input fip/bl30_new.bin.g12a.enc \ --output fip/bl30_new.bin.enc \ --level v3 --type bl30 $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl3sig --input fip/bl31.img \ --output fip/bl31.img.enc \ --level v3 --type bl31 $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl3sig --input fip/bl33.bin --compress lz4 \ --output fip/bl33.bin.enc \ --level v3 --type bl33 --compress lz4 $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl2sig --input fip/bl2_new.bin \ --output fip/bl2.n.bin.sig $ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bootmk \ --output fip/u-boot.bin \ --bl2 fip/bl2.n.bin.sig \ --bl30 fip/bl30_new.bin.enc \ --bl31 fip/bl31.img.enc \ --bl33 fip/bl33.bin.enc \ --ddrfw1 fip/ddr4_1d.fw \ --ddrfw2 fip/ddr4_2d.fw \ --ddrfw3 fip/ddr3_1d.fw \ --ddrfw4 fip/piei.fw \ --ddrfw5 fip/lpddr4_1d.fw \ --ddrfw6 fip/lpddr4_2d.fw \ --ddrfw7 fip/diag_lpddr4.fw \ --ddrfw8 fip/aml_ddr.fw \ --ddrfw9 fip/lpddr3_1d.fw \ --level v3 Then write the image to SD or eMMC with: .. code-block:: bash $ DEV=/dev/boot_device $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1 $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=440 |