Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 | Freescale MCF5475EVB ColdFire Development Board ================================================ TsiChung Liew(Tsi-Chung.Liew@freescale.com) Created Jan 08, 2008 =========================================== Changed files: ============== - board/freescale/m547xevb/m547xevb.c Dram setup, IDE pre init, and PCI init - board/freescale/m547xevb/mii.c MII init - board/freescale/m547xevb/Makefile Makefile - board/freescale/m547xevb/config.mk config make - board/freescale/m547xevb/u-boot.lds Linker description - cpu/mcf547x_8x/cpu.c cpu specific code - cpu/mcf547x_8x/cpu_init.c Flexbus ChipSelect, Mux pins setup, icache and RTC extra regs - cpu/mcf547x_8x/interrupts.c cpu specific interrupt support - cpu/mcf547x_8x/slicetimer.c Timer support - cpu/mcf547x_8x/speed.c system, pci, flexbus, and cpu clock - cpu/mcf547x_8x/Makefile Makefile - cpu/mcf547x_8x/config.mk config make - cpu/mcf547x_8x/start.S start up assembly code - doc/README.m5475evb This readme file - drivers/dma/MCD_dmaApi.c DMA API functions - drivers/dma/MCD_tasks.c DMA Tasks - drivers/dma/MCD_tasksInit.c DMA Tasks Init - drivers/net/fsl_mcdmafec.c ColdFire common DMA FEC driver - drivers/serial/mcfuart.c ColdFire common UART driver - include/MCD_dma.h DMA header file - include/MCD_progCheck.h DMA header file - include/MCD_tasksInit.h DMA header file - include/asm-m68k/bitops.h Bit operation function export - include/asm-m68k/byteorder.h Byte order functions - include/asm-m68k/errno.h Error Number definition - include/asm-m68k/fec.h FEC structure and definition - include/asm-m68k/fsl_i2c.h I2C structure and definition - include/asm-m68k/fsl_mcddmafec.h DMA FEC structure and definition - include/asm-m68k/global_data.h Global data structure - include/asm-m68k/immap.h ColdFire specific header file and driver macros - include/asm-m68k/immap_547x_8x.h mcf547x_8x specific header file - include/asm-m68k/io.h io functions - include/asm-m68k/m547x_8x.h mcf547x_8x specific header file - include/asm-m68k/posix_types.h Posix - include/asm-m68k/processor.h header file - include/asm-m68k/ptrace.h Exception structure - include/asm-m68k/rtc.h Realtime clock header file - include/asm-m68k/string.h String function export - include/asm-m68k/timer.h Timer structure and definition - include/asm-m68k/types.h Data types definition - include/asm-m68k/uart.h Uart structure and definition - include/asm-m68k/u-boot.h u-boot structure - include/configs/M5475EVB.h Board specific configuration file - lib_m68k/board.c board init function - lib_m68k/cache.c - lib_m68k/interrupts Coldfire common interrupt functions - lib_m68k/m68k_linux.c - lib_m68k/traps.c Exception init code 1 MCF547x specific Options/Settings ==================================== 1.1 pre-loader is no longer suppoer in thie coldfire family 1.2 Configuration settings for M5475EVB Development Board CONFIG_MCF547x_8x -- define for all MCF547x_8x CPUs CONFIG_M547x -- define for all Freescale MCF547x CPUs CONFIG_M5475 -- define for M5475EVB board CONFIG_MCFUART -- define to use common CF Uart driver CFG_UART_PORT -- define UART port number, start with 0, 1 and 2 CONFIG_BAUDRATE -- define UART baudrate CONFIG_FSLDMAFEC -- define to use common dma FEC driver CONFIG_NET_MULTI -- define to use multi FEC in u-boot CONFIG_MII -- enable to use MII driver CONFIG_CF_DOMII -- enable to use MII feature in cmd_mii.c CFG_DISCOVER_PHY -- enable PHY discovery CFG_RX_ETH_BUFFER -- Set FEC Receive buffer CFG_FAULT_ECHO_LINK_DOWN-- CFG_FEC0_PINMUX -- Set FEC0 Pin configuration CFG_FEC1_PINMUX -- Set FEC1 Pin configuration CFG_FEC0_MIIBASE -- Set FEC0 MII base register CFG_FEC1_MIIBASE -- Set FEC0 MII base register MCFFEC_TOUT_LOOP -- set FEC timeout loop CONFIG_HAS_ETH1 -- define to enable second FEC in u-boot CONFIG_CMD_USB -- enable USB commands CONFIG_USB_OHCI_NEW -- enable USB OHCI driver CONFIG_USB_STORAGE -- enable USB Storage device CONFIG_DOS_PARTITION -- enable DOS read/write CONFIG_SLTTMR -- define to use SLT timer CONFIG_FSL_I2C -- define to use FSL common I2C driver CONFIG_HARD_I2C -- define for I2C hardware support CONFIG_SOFT_I2C -- define for I2C bit-banged CFG_I2C_SPEED -- define for I2C speed CFG_I2C_SLAVE -- define for I2C slave address CFG_I2C_OFFSET -- define for I2C base address offset CFG_IMMR -- define for MBAR offset CONFIG_PCI -- define for PCI support CONFIG_PCI_PNP -- define for Plug n play support CONFIG_SKIPPCI_HOSTBRIDGE -- SKIP PCI Host bridge CFG_PCI_MEM_BUS -- PCI memory logical offset CFG_PCI_MEM_PHYS -- PCI memory physical offset CFG_PCI_MEM_SIZE -- PCI memory size CFG_PCI_IO_BUS -- PCI IO logical offset CFG_PCI_IO_PHYS -- PCI IO physical offset CFG_PCI_IO_SIZE -- PCI IO size CFG_PCI_CFG_BUS -- PCI Configuration logical offset CFG_PCI_CFG_PHYS -- PCI Configuration physical offset CFG_PCI_CFG_SIZE -- PCI Configuration size CFG_MBAR -- define MBAR offset CONFIG_MONITOR_IS_IN_RAM -- Not support CFG_INIT_RAM_ADDR -- defines the base address of the MCF547x internal SRAM CFG_CSn_BASE -- defines the Chip Select Base register CFG_CSn_MASK -- defines the Chip Select Mask register CFG_CSn_CTRL -- defines the Chip Select Control register CFG_SDRAM_BASE -- defines the DRAM Base 2. MEMORY MAP UNDER U-BOOT AND LINUX KERNEL =========================================== 2.1. System memory map: Flash: 0xFF800000-0xFFFFFFFF (8MB) DDR: 0x00000000-0x3FFFFFFF (1024MB) SRAM: 0xF2000000-0xF2000FFF (4KB) PCI: 0x70000000-0x8FFFFFFF (512MB) IP: 0xF0000000-0xFFFFFFFF (256MB) 3. COMPILATION ============== 3.1 To create U-Boot the gcc-4.x compiler set (ColdFire ELF or uclinux version) from codesourcery.com was used. Download it from: http://www.codesourcery.com/gnu_toolchains/coldfire/download.html 3.2 Compilation export CROSS_COMPILE=cross-compile-prefix cd u-boot-1.x.x make distclean make M5475AFE_config, or - boot 2MB, RAM 64MB make M5475BFE_config, or - boot 2MB, code 16MB, RAM 64MB make M5475CFE_config, or - boot 2MB, code 16MB, Video, USB, RAM 64MB make M5475DFE_config, or - boot 2MB, USB, RAM 64MB make M5475EFE_config, or - boot 2MB, Video, USB, RAM 64MB make M5475FFE_config, or - boot 2MB, code 32MB, Video, USB, RAM 128MB make M5475GFE_config, or - boot 2MB, RAM 64MB make 5. SCREEN DUMP ============== 5.1 U-Boot 1.3.1 (Jan 8 2008 - 12:47:44) CPU: Freescale MCF5475 CPU CLK 266 Mhz BUS CLK 133 Mhz Board: Freescale FireEngine 5475 EVB I2C: ready DRAM: 64 MB FLASH: 18 MB In: serial Out: serial Err: serial Net: FEC0, FEC1 -> pri bootdelay=1 baudrate=115200 ethaddr=00:e0:0c:bc:e5:60 eth1addr=00:e0:0c:bc:e5:61 ipaddr=192.162.1.2 serverip=192.162.1.1 gatewayip=192.162.1.1 netmask=255.255.255.0 hostname=M547xEVB netdev=eth0 loadaddr=10000 u-boot=u-boot.bin load=tftp ${loadaddr) ${u-boot} upd=run load; run prog prog=prot off bank 1;era ff800000 ff82ffff;cp.b ${loadaddr} ff800000 ${filesize};save stdin=serial stdout=serial stderr=serial ethact=FEC0 mem=65024k Environment size: 433/8188 bytes -> bdin memstart = 0x00000000 memsize = 0x04000000 flashstart = 0xFF800000 flashsize = 0x01200000 flashoffset = 0x00000000 sramstart = 0xF2000000 sramsize = 0x00001000 mbar = 0xF0000000 busfreq = 133.333 MHz pcifreq = 0 MHz ethaddr = 00:E0:0C:BC:E5:60 eth1addr = 00:E0:0C:BC:E5:61 ip_addr = 192.162.1.2 baudrate = 115200 bps -> ? ? - alias for 'help' autoscr - run script from memory base - print or set address offset bdinfo - print Board Info structure boot - boot default, i.e., run 'bootcmd' bootd - boot default, i.e., run 'bootcmd' bootelf - Boot from an ELF image in memory bootm - boot application image from memory bootp - boot image via network using BootP/TFTP protocol bootvx - Boot vxWorks from an ELF image cmp - memory compare coninfo - print console devices and information cp - memory copy crc32 - checksum calculation dcache - enable or disable data cache echo - echo args to console erase - erase FLASH memory flinfo - print FLASH memory information go - start application at address 'addr' help - print online help icache - enable or disable instruction cache icrc32 - checksum calculation iloop - infinite loop on address range imd - i2c memory display iminfo - print header information for application image imls - list all images found in flash imm - i2c memory modify (auto-incrementing) imw - memory write (fill) inm - memory modify (constant address) iprobe - probe to discover valid I2C chip addresses itest - return true/false on integer compare loadb - load binary file over serial line (kermit mode) loads - load S-Record file over serial line loady - load binary file over serial line (ymodem mode) loop - infinite loop on address range md - memory display mii - MII utility commands mm - memory modify (auto-incrementing) mtest - simple RAM test mw - memory write (fill) nfs - boot image via network using NFS protocol nm - memory modify (constant address) pci - list and access PCI Configuration Space ping - send ICMP ECHO_REQUEST to network host printenv- print environment variables protect - enable or disable FLASH write protection rarpboot- boot image via network using RARP/TFTP protocol reset - Perform RESET of the CPU run - run commands in an environment variable saveenv - save environment variables to persistent storage setenv - set environment variables sleep - delay execution for some time tftpboot- boot image via network using TFTP protocol usb - USB sub-system usbboot - boot from USB device version - print monitor version -> usb start (Re)start USB... USB: OHCI pci controller (1131, 1561) found @(0:17:0) OHCI regs address 0x80000000 scanning bus for devices... 2 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found -> |