Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 | /* SPDX-License-Identifier: GPL-2.0+ */ /* * Copyright (C) 2018 Allied Telesis Labs */ #ifndef _CONFIG_X530_H #define _CONFIG_X530_H /* * High Level Configuration Options (easy to change) */ #define CONFIG_DISPLAY_BOARDINFO_LATE #define CONFIG_SYS_TCLK 250000000 /* 250MHz */ /* * NS16550 Configuration */ #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK #if !defined(CONFIG_DM_SERIAL) #define CONFIG_SYS_NS16550_REG_SIZE (-4) #define CONFIG_SYS_NS16550_COM1 MV_UART_CONSOLE_BASE #endif /* * Serial Port configuration * The following definitions let you select what serial you want to use * for your console driver. */ #define CONFIG_CONS_INDEX 1 /*Console on UART0 */ /* * Commands configuration */ #define CONFIG_CMD_PCI /* NAND */ #define CONFIG_SYS_NAND_ONFI_DETECTION #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define BBT_CUSTOM_SCAN #define BBT_CUSTOM_SCAN_PAGE 0 #define BBT_CUSTOM_SCAN_POSITION 2048 /* SPI NOR flash default params, used by sf commands */ #define MTDIDS_DEFAULT "nand0=nand" #define MTDPARTS_DEFAULT "mtdparts=nand:240M(user),8M(errlog),8M(nand-bbt)" #define MTDPARTS_MTDOOPS "errlog" /* Partition support */ /* Additional FS support/configuration */ /* USB/EHCI configuration */ #define CONFIG_EHCI_IS_TDI /* Environment in SPI NOR flash */ #define CONFIG_PHY_MARVELL /* there is a marvell phy */ #define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */ /* PCIe support */ #ifndef CONFIG_SPL_BUILD #define CONFIG_PCI_SCAN_SHOW #endif /* NAND */ #define CONFIG_SYS_NAND_ONFI_DETECTION #define CONFIG_CMD_UBI #define CONFIG_CMD_UBIFS #define CONFIG_LZO #define CONFIG_CMD_MTDPARTS #define CONFIG_SYS_MALLOC_LEN (4 << 20) #include <asm/arch/config.h> /* * Other required minimal configurations */ #define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */ #define CONFIG_SYS_ALT_MEMTEST /* Keep device tree and initrd in low memory so the kernel can access them */ #define CONFIG_EXTRA_ENV_SETTINGS \ "fdt_high=0x10000000\0" \ "initrd_high=0x10000000\0" #define CONFIG_SYS_LOAD_ADDR 0x1000000 #define CONFIG_UBI_PART user #define CONFIG_UBIFS_VOLUME user /* SPL */ /* Defines for SPL */ #define CONFIG_SPL_SIZE (140 << 10) #define CONFIG_SPL_MAX_SIZE (CONFIG_SPL_SIZE - 0x0030) #define CONFIG_SPL_BSS_START_ADDR (0x40000000 + CONFIG_SPL_SIZE) #define CONFIG_SPL_BSS_MAX_SIZE (16 << 10) #ifdef CONFIG_SPL_BUILD #define CONFIG_SYS_MALLOC_SIMPLE #endif #define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10)) #define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4) /* SPL related SPI defines */ #define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_SPI_U_BOOT_OFFS #endif /* _CONFIG_X530_H */ |